On November 5th, the United States launched an LGM-30G Minuteman III ICBM from Vandenberg Space Force Base in California. Roughly 30 minutes later the three warheads onboard struck their targets 4,200 miles (6,759 km) away at the Reagan Test Site in the Marshall Islands. What is remarkable about this test is not that one of these ICBMs was fired — as this is regularly done to test the readiness of the US’ ICBMs — but rather that it carried three warheads instead of a single one.

Originally the Minuteman III ICBMs were equipped with three warheads, but in 2014 this was reduced to just one as a result of arms control limits agreed upon with Russia. This New Start Treaty expires in 2026 and the plan is to put three warheads back in the 400 operational Minuteman III ICBMs in the US’ arsenal. To this end a validation test had to be performed, yet a 2023 launch failed. So far it appears that this new launch has succeeded.

Although the three warheads in this November 5 launch were not nuclear warheads but rather Joint Test Assemblies, one of them contained more than just instrumentation to provide flight telemetry. In order to test the delivery vehicle more fully a so-called ‘high-fidelity’ JTA was also used which is assembled much like a real warhead, including explosives. The only difference being that no nuclear material is present, just surrogate materials to create a similar balance as the full warhead.

Assuming the many gigabytes of test data checks out these Minuteman III ICBMs should be ready to serve well into the 2030s at which point the much-delayed LGM-35 Sentinel should take over.

Nerf blasters are fun and all, but flinging foam can get old. Picking it up again, even moreso. This blaster from [Concept Crafted Creations] gets around that annoying problem by shooting ice instead. 

The concept was to build a better water gun with longer range—and what better way to do that than by shooting ice instead? The blaster relies on a PVC air tank for propulsion—one of the most controversial design choices you can make if you read the comments around here. It’s charged by a small air compressor, and dumping the air is handled by a solenoid valve. So far, so simple.

What makes this blaster special is where it gets its ammunition from. The blaster uses a custom CNC-machined block from PCBway to act as a freeze chamber. Water enters an aluminum block, and is cooled by thermoelectric elements. Once the projectile has frozen inside the chamber, it’s stuck in place, so the chamber is then heated by a small heating element. This melts the projectile just enough to allow it to be fired.

It’s a complicated but ingenious way of building an ice blaster. It does pack some real punch, too. It shoots the ice projectiles hard enough to shatter wine glasses. That’s enough to tell us you don’t want to be aiming this thing at your pals in a friendly match of Capture the Flag. Stick to paintballs, perhaps. Video after the break.

Although we think of air-to-air radar as a relatively modern invention, it first made its appearance in WWII. Some late war fighters featured the AN/APS-13 Tail Warning Radar to alert the pilot when an enemy fighter was on his tail. In [WWII US Bombers]’ fascinating video we get a deep dive into this fascinating piece of tech that likely saved many allied pilots’ lives.

Fitted to aircraft like the P-51 Mustang and P-47 Thunderbolt, the AN/APS-13 warns the pilot with a light or bell if the aircraft comes within 800 yards from his rear. The system consisted of a 3-element Yagi antenna on the vertical stabilizer, a 410 Mhz transceiver in the fuselage, and a simple control panel with a warning light and bell in the cockpit.

In a dogfight, this allows the pilot to focus on what’s in front of him, as well as helping him determine if he has gotten rid of a pursuer. Since it could not identify the source of the reflection, it would also trigger on friendly aircraft, jettisoned wing tanks, passing flak, and the ground. This last part ended up being useful for safely descending through low-altitude clouds.

This little side effect turned out to have very significant consequences. The nuclear bombs used on Hiroshima and Nagasaki each carried four radar altimeters derived from the AN/APS-13 system.

This DIY lasertag project designed by [Nii], which he brought to Tokyo Maker Faire back in September, is a treasure trove. It’s all in Japanese and you’ll need to visit X (formerly Twitter) to see it, but the images do a fine job of getting the essentials across and your favorite translator tool will do a fair job of the rest.

There’s a whole lot to admire in this project. The swing-out transparent OLED display is super slick, the electronics are housed on a single PCB, the back half of the grip is in fact a portable USB power bank that slots directly in to provide power, and there’s a really smart use of a short RGB LED strip for effects.

The optical elements show some inspired design, as well. An infrared LED points forward, and with the help of a lens, focuses the beam tightly enough to make aiming meaningful. For detecting hits, the top of the pistol conceals a custom-made reflector that directs any IR downward into a receiver, making it omnidirectional in terms of hit sensing but only needing a single sensor.

Want to know more? Check out [Nii]’s earlier prototypes on his website. It’s clear this has been in the works for a while, so if you like seeing how a project develops, you’re in for a treat.

As for the choice of transparent OLED displays? They are certainly cool, and we remember how wild it looks to have several stacked together.